Search results

to be honest i think the d4-3 was shagged didnt have my tester with me but it was just to say my d6-3 was fine as i use those all the time so i have a few all the time dont bother with d4-3 that much so no resevre

did a wet dash with cpi today using my g4 the d4-3 wouldnt do it put my d6-3 back in looks great turning a bit fast but two light passes i found better

yes thats wot i thought do you think do away with texture gun and use a standard with 12mm cap as i am using texture gun with 10mm nozzle

have i started something

yes seen the vid soz that is r+s i am using just found texturing gun was bit better but it does block from time to time

anybody done much texturing with g4 using weber mono and what setup did you use . done a couple of houses last week with d4-3 and texturing gun with 10mm nozzle still not quite happy still think it needs slowing down a bit any advise thanks . oh i spray 10mm first mesh rule leave hour or so then...

it sounds like you may be best using a weber insulation system to reduce any risk of cracking you could build out the qouins first then they would still stand proud webers m1 leaves same scratch finish the insulation batts can be mechanicly fixed to exsiting wall and bridgeing new work to old...

sorry pal just a little shy ha ha

no

sorry that was for thebones

no i dont and yes it does

if that water bottle dont rise tommoz the hose is going up rich,s arse

yes brass connecter from water bottle hose to the chamber

no quite new pump

g4 light

same as we always use 25 meters the prob has just appeared overnight be spraying years just this prob has never poped up unless the filters blocked or pressure crap

yes fiters checked in machine and filter in water pump i am running from mains with not to bad pressure thanks

yes released all the air through the tap like i always do its just one of them probs that was not there last night but there this morning doing my head in

the past two days when i set my water it wont go above 300 in the water bottle water pressure is fine as i am working my pump all ok at the minute as rotor nand stator is worn in but when i come to change them prob tommoz i prefer to start up with water a lot higher any ideas would be great dont...

nissan navara drives perfect with roof rack and 12 month old trailer to carry geny and g4 nice clean condition £4,500 map px transit size van must have good engine as travel lots of miles

this is so true i been spraying for about 5 years with my gang of three we used to swap around every day who ran the machine and play tricks on each other like turn the water off kink the air line etc just for the less experieced person to solve so now it is much easier you dont have to keep...

fix a battern at coure below sit beads on top we also nail dpc to battern to protect blues when spraying

my g4 is over 20 years old it runs like a dream

yes we are getting some build up in the chamber we are using a twister rotor and stator the stuff we are using takes one day per mil to dry and we are having to put upto 50mm on with feature work but it does not like going on much more than 15mm at a time so 15 days before next 15-20 mil this is...

has anybody used limtec through a g4 i am having loads of probs using 25mm hose 20meters long back pressure is around 35bar can not go any wetter any advise would be great

what would you all say the best way to cure damp after injection i was thinking sbr, coat of sand cement then renovating plaster then skim what are your thoughts

not to bothered it good when you do 3 hits you can be in the van for 2.30-3oclock

been skimming this week have not skimmed for ages i mainly render now the blue sound block boards go off so quick any reason why

have any of u lot ever skimmed a house on site u are lucky to get 2.50 per metre on prob only a pound on a dodgey 3 storey stairwell

it was very messy i was purple when finished

done a 90sq metre ceiling in 6mm stolit k on fri had to use sponge float to apply as no chance with steel trowel anyone got any other ideas on how to apply 6mm on ceilings

been rendering for years with weber sto etc always use rendaid great stuff make sure you key the rend aid i dab with old brush head