Search results

Anyone used a A3-2l r&s for better control with bucket coats?

Don't give me no b*ll***s that it has been done before. took a chance today I knew that I was cutting it close with with bucket coat and I ran out of gear I had about 4m left to do so I laid the leading edge on thicker and bedded cling wrap into it, two-and-a-half hours later I got back with a...

I'm stating the obvious with this review, and already knew what was going to happen but to help tapit out this was my verdict, Winged/mesh beads are used on lots of my work that include ewi and carrier board so it's a nonstarter as the fitting process needs to be done with render, Every stop...

Anyone putting plasticiser in hi polymer base coats through the machine

Pft 402 compressor, Swing gun set in case, 25m remote cable, All brand new just had three tubs off acrylic through it to test out, I've got exactly the same setup on a another machine brought the additional set up but can't get the staff to use it £2400 worth will take 2 grand or nearest offer...

https://www.swindonadvertiser.co.uk/news/18603239.swindon-parking-warden-sprayed-plaster-dispute-ticket/

Anyone put the b4-2l on the ritmo m? @McPlaster @Vincey

What's your favourite base coat based on workability and nice to spray?

Any one used it yet? https://parex.co.uk/General_Construction_-_New_Build/Rendering_-_Cement/Base_Coats_-_Cement/Multi_Purpose_Render.aspx?fbclid=IwAR3NRt5mCWRdlYaZsVezt0D5jUetubqkfMh1ZDuLWwunka_c8nWXwQvrLZg

https://www.gypsumtools.com/dewalt-ultra-flex-14-finishing-trowel.html

Thought I would just test it out, When measuring up a job and take the area of a wall and deduct glazing Sometimes it can be a b*****d with the high up Windows without scaffolding

Use a local reputable business, That's an approved applicator, That machine applies That can give you references and addresses in your local area to jobs that are completed, Don't try and get it done on the cheap, If your job doesn't meet the criteria it's going to look s**t

I'm about to get a new website built I've outgrown mine and want a really decent one any recommendations

Mate off mine been using it last couple of days he runs quite a few lads, Bad news it's meant to be dog s**t None of them can get on with it

As above

Is anyone getting new inquiries, has the phone gone dead, my phone's gone crazy over the last week, think people are panicking because there not getting there booked in trade's and ringing around being c**** trying to replace, all need to work doing ASAP scaffold up

https://www.ebay.co.uk/itm/264670443697

Extension only 10 years old and being redone

Looks mint don't no how good they are Small machine might be handy,https://www.ebay.co.uk/itm/303500635644

It's got to be a common fullt that someone knows the straight answer to It's been fine until Friday now it's tripping the electric and I'm having to wear Marigold's again, my ear got a shock as well Someone must have fixed this and know the answer

Noticed from a lot of old posts that pft used to come on here, did they get bombarded with questions about machines so got stick of it?

Took my lad out on his new Christmas present in the middle of nowhere down a dirt track 20 miles from home, went down a pothole and concrete went through the sump of the van, we had to walk miles to get oil whilst pinkgrip was drying, got me home amazing stuff!!

Anyone experienced put in a septic tank in with high water table, the hole has got to be 12 ft water table is at 4 ft,

:tonto:Held a 45 mil piece of timber steady whilst using 90 ml nails

I've just completely redone my own place complete renovation, I can't get the heating on until December, sprayed it all out yesterday I'm concerned about moisture and and mould got a new Oak kitchen coming on Monday don't want moisture getting into it and the doors swelling etc, any...

Anyone used this much do you find adding water is counteracting it

@malc, electric tripping I was getting in a right panic couldn't sort it out ringing around no one had a sensible answer found this old thread, worked a treat(y)

https://www.expressandstar.com/news/crime/2019/10/17/plasterer-jailed-after-punching-man-for-talking-to-his-girl/

?

https://www.birminghammail.co.uk/news/uk-news/dads-fury-after-builder-poo-16848174

386m thin coat job booked in for a fortnight's time, Drove past today and someones f****** started it it's like a patchwork breaking the walls up, apparently they started fortnight ago and there's only about 50 m Done, I hope it's all f****** falls off for the c***

https://www.thesun.co.uk/news/9827591/cowboy-builders-slept-beds-ate-food/

Anyone use the serrated darby with wooden handle on base coat, are they any good ?

Why does base coat go off so quick through the my ritmo, as soon as it hits the wall it's hard to work with but when you hand apply it hangs around for ages?

The threaded caps on water level gauge have cracked on my ritmo, Can you just buy the caps or have you got a buy the whole new gauge, and do you have to take the brass nut off underneath to get it off, Any help appreciated cheers

Might be worth a try bit expensive though

Might be worth a try