D
Deleted member 40920
Guest
Why are some brands of beads about 75-80 degrees rather than 90? Pain in the arse
E.U
Shes here BG snake!!!!
Djr
Well-Known Member
Them minimesh beads are utter shite
JessThePlasterer
Queen Jess Elizabeth I
Yup! Used them today because wickes didn’t have any solid. Putting them on a lintel situation sucks. Just know they’re going to show through in places.
I’ve clouted the f**k out of them! Then hammered my finger which actually brought tears to my eyes. So went home like a big tantrumming baby!
Vincey
Private Member
I posted a thread about them a few months back mate , same reason as the op says , it’s like every other bead available is the wrong angle on purpose
JessThePlasterer
Queen Jess Elizabeth I
I would like to know why, why for the love of Thor, if they insist on sticking barcodes on them why can’t they go on the very end of the bead where it’s more likely to get chopped off!!!
Or even the back of the bead!!!!!
JessThePlasterer
Queen Jess Elizabeth I
So f**k**g annoying! I run a lighter over them and then they just peel off but still!
I just leave them on and moan like f**k to anyone else thats on job!!!!
Mouldyoldspudgun
Well-Known Member
Ah chris hemsworth fan aye? Does ones beloved know?
Vincey
Private Member
Robbo get a box and give a honest review mate
Bg thincoat beads
Never even seen them before tbh , picked up 6 yesterday from someone else’s order at merchants and used today,Flatter and wider and better fit to edges than any others I used , slightly more on cost as normal but for how they are compared to others I’ll buy them again £1.40 inc vat but...
www.plasterersforum.com
JessThePlasterer
Queen Jess Elizabeth I
I’d switch Si out for him in a heartbeat!!
But no that’s not my reasoning, I just like mixing it up! May as well lean on the lineage
ChrispyUK
Well-Known Member
tapit
Well-Known Member
i just stick a piece of tape over the barcode.
hollybank
Private Member
Because joiners cant put up a 45degree corner on studwork.
D
Deleted member 40920
Guest
Ouch
Pmsl!
Donzo
Well-Known Member
Never seen a bg one or stockist in my life
essexandy
The Lake Governor
I don't know about all the different manufacturers but if you take a look at the Catnic catalogue it shows two almost identical looking beads. One is set at 90° and is for skimming (drywall) and the other (can't remember the exact angle) is set to allow a 6mm coat (thin coat).
I'm not sure if they still do, but BG used to state that high quality work on plasterboard should be Bond and set. Hence 6mm beads.
Pete the BG beads are superb, but far too expensive even if being bought in decent quantities.
I'm not sure if they still do, but BG used to state that high quality work on plasterboard should be Bond and set. Hence 6mm beads.
Pete the BG beads are superb, but far too expensive even if being bought in decent quantities.
Mouldyoldspudgun
Well-Known Member
I understand now, I forgot about your ancestry
Vincey
Private Member
Me neither till I seen those ones in travis a guy who does all the new build sites in my town ordered them in because the plasterers were sick of all the other beads available
JessThePlasterer
Queen Jess Elizabeth I
Link Removed
essexandy
The Lake Governor
What for skimming?
Yes pal.
Mouldyoldspudgun
Well-Known Member
That’s exactly how I have imagined you, I must be psychic
essexandy
The Lake Governor
Crikey I'm always moaning about normal beads allowing too much thickness.
Actually that's what I noticed about the BG beads, they allowed a nice thin (2mm) coat.
I think their claim of 6mm is abit generous but they defo thicker than the norm...... But love them as alot of corners i bed onto are all over the place so give you scope to build out and still cover the wings.... I staple mini mesh for board.....