First ritmo job

Yeah good little machine, till i kinked the hose, school boy error!! That’s k rend silicone k1 with soft r&s went through fine. Had about 6-7 bags in the hopper when it kinked [emoji85] sprayed about 20 bags had to handball last 15.


Sent from my iPhone using Tapatalk
 
Topspread16 said:
Yeah good little machine, till i kinked the hose, school boy error!! That’s k rend silicone k1 with soft r&s went through fine. Had about 6-7 bags in the hopper when it kinked [emoji85] sprayed about 20 bags had to handball last 15.


Sent from my iPhone using Tapatalk
Click to expand...
Nice one looks good
 
Link RemovedLink RemovedLink Removed
One I’ve just been back to finish under the belcast in green ft, started it last summer. Was waiting on ground levels. Anybody’s cup of tea with the green? I’m unsure.


Sent from my iPhone using Tapatalk
 
The old kink in the pipe trick. How did you find the K1 to spray. Wasn't a fan of it. Looks a canny job though marra
The orange army marches on
 
Topspread16 said:
Link RemovedLink RemovedLink Removed
One I’ve just been back to finish under the belcast in green ft, started it last summer. Was waiting on ground levels. Anybody’s cup of tea with the green? I’m unsure.


Sent from my iPhone using Tapatalk
Click to expand...
i like the green works well with doors and the colour of render
 
Arti said:
The old kink in the pipe trick. How did you find the K1 to spray. Wasn't a fan of it. Looks a canny job though marra
The orange army marches on
Click to expand...

I found it alright, had at just over 225. It’s mainly what I use, only that and Weber on the shelf round here. I don’t advertise either so it’s a case of “oh that looks well what is it?” K rend. I find it’s not the best but hard to push other products on when they’ve seen k. They get sucked in to the shiny flecks.


Sent from my iPhone using Tapatalk
 
Topspread16 said:
First job with the ritmo, didn’t go fully to plan but got there in the end. Link Removed


Sent from my iPhone using Tapatalk
Click to expand...
Topspread16 said:
Yeah good little machine, till i kinked the hose, school boy error!! That’s k rend silicone k1 with soft r&s went through fine. Had about 6-7 bags in the hopper when it kinked [emoji85] sprayed about 20 bags had to handball last 15.


Sent from my iPhone using Tapatalk
Click to expand...
which hose kinked?ive done about everything wrong except that
 
Rondo, f**k*r to clean out without the jet wash. Drove the van over it back and forth. Soon cleared it.


Sent from my iPhone using Tapatalk
 
Topspread16 said:
Rondo, f**k*r to clean out without the jet wash. Drove the van over it back and forth. Soon cleared it.


Sent from my iPhone using Tapatalk
Click to expand...
Ha!a done that second spray,bought dino rods mash hammer tried everything,took it to les he flushed it out in two minutes with this small hose that you feed inside,i bought one on the spot just incase,blocked it again next day like a tit trying too push gear theough too stiff so proper lesson learnt
 
Might be worth buying one then, if I did it first spray it’s going to happen again.


Sent from my iPhone using Tapatalk
 
Ive never done it since tbh ,just done a load of other stupod stuff.overthinking probably always had my whisk on standby!becomes second mature after so long,still to master thin coat systems as ive mainly done mono this summer ,wish i had bought one ten years ago great machines
 
You must log in or register to reply here.

Share this page

Back
Top