Joining the Rendabot crew.

[keithuk]

Using 2 tubs wicks (10Lts) to 220 water butt , normally ready about 1.00 pm mate


Sent from my iPhone using Tapatalk

 

[SpankySouthport]

Using 2 tubs wicks (10Lts) to 220 water butt , normally ready about 1.00 pm mate


Sent from my iPhone using Tapatalk

Wow 1pm!? what time do you have it on by 7 [emoji15]

 

[keithuk]

No later then 11.00 am mate


Sent from my iPhone using Tapatalk

 

[user__removed]

Parex is holding for 12 hrs overnight easy at the moment.@SpankySouthport

 

[SpankySouthport]

No later then 11.00 am mate


Sent from my iPhone using Tapatalk

You working in this cold or you not bother??

 

[SpankySouthport]

Parex is lasting easy 15 hrs overnight at the moment @SpankySouthport

In an ideal world I would use parex but they already picked silver pearl from another one we did [emoji29]

 

[keithuk]

It's the lads that leave it wet over night would be more a worry when it can be -2 , we don't work lower then 4 rising on a same day , I might be beading tomorrow ! Lol


Sent from my iPhone using Tapatalk

 

[user__removed]

If its forecast as low as -2 overnight forget it I reckon.

 

[SpankySouthport]

We had a nice few days, well no rain freezing though, thought we may have been good to go and get started on some of the render that's been piling up over the past 4 months.. Obviously not

We booked in solid for 2-3 months from the start of March fingers crossed we can get started :-/

Had a really mild winter though so I'm half expecting a winter in March just the f**k us over

 

[Rossi46]

We had a nice few days, well no rain freezing though, thought we may have been good to go and get started on some of the render that's been piling up over the past 4 months.. Obviously not

We booked in solid for 2-3 months from the start of March fingers crossed we can get started :-/

Had a really mild winter though so I'm half expecting a winter in March just the f**k us over

Sounds good Ben! Hope you can get a start and everything goes like clockwork

 

[User___removed]

It's the lads that leave it wet over night would be more a worry when it can be -2 , we don't work lower then 4 rising on a same day , I might be beading tomorrow ! Lol


Sent from my iPhone using Tapatalk

Your not bothered about the frost getting in what you done in the day then Keith?

 

[user__removed]

Hes put s**t loads of frost proofer in it so I doubt it.

 

[User___removed]

Yeah but the frost proof helps it go off not stop the frost getting in!!
Just curious as if it gets below -1 over night its risky

 

[keithuk]

Your not bothered about the frost getting in what you done in the day then Keith?

Yes mate i do look at the whole picture ,it will cost me to put it right ,not a road i want to go down

 

[user__removed]

I thought it was called frostproofer and rapid hardener! The label is misleading.

 

[keithuk]

I thought it was called frostproofer and rapid hardener! The label is misleading.

I think with the water content far lower ,it does reduce the risk over night ,as you know with mono it has to be dry to finish it

 

[User___removed]

I think with the water content far lower ,it does reduce the risk over night ,as you know with mono it has to be dry to finish it

Good point.
With say a sand & cement finish it will have a higher risk I imagine due to that

 

[Rigsby]

A frost proofer is what it says, a frost proofer. Anti freeze in our car radiators is a frost proofer. Although I would think the car radiator stuff is more powerful.

-1 is a ground frost think it is minus 3 and beyond before it goes into vertical surfaces but you have to also consider heat loss.

I have never seen the effects of frost getting into render only render blowing off after being saturated from water coming out of overflows.

 

[SpankySouthport]

Sounds good Ben! Hope you can get a start and everything goes like clockwork

Haha as if anything ever goes like clockwork [emoji28]

 

[Rossi46]

Haha as if anything ever goes like clockwork [emoji28]

As positive as one tries to be one always finds one sweating ones tits off and stressing like fook haha

 

[Jrend]

In an ideal world I would use parex but they already picked silver pearl from another one we did [emoji29]

Get g00 Ben they will never know the difference. Weber is fine over night anyway. We put accelerator in for over nighters last week.

 

[owls]

So it looks like I'm investing and going to be joining you all.

After some helpful info from both @bobby and @owls I'm getting myself a Ritmo L.
Thanks for the advice lads much appreciated [emoji106].

It seems like an investment I need to make with the amount of rendering we have been doing I just hope it bloody continues!

I also had a very good chat with Ian from @PFTwales who's also advised me on getting the Ritmo.
I did try to speak to Ryan last week at Plasterersonestopshop and was told he'd call me back but never heard nothing.

I'm in the process of sorting finance then will be calling Ian to place the order and join the crew.
Will be taking my lads up for a training day once it's in I just hope England have beat Wales by then or its after I pick it up! Couldn't handle the banter if we lose [emoji33][emoji23]


Sent from my iPhone using Tapatalk

Welcome to 21st century rendering,
Have you got rid of your type writer yet, and bought a computer to do your invoices on aswell?

 

[Arti]

Slightly off topic but owls post reminded me off the old fella we get skips off. I popped into the yard to square him up and I asked his marra if he could get the old fella to email me over the receipts he replied " email. The old bustard still has a black and white Tele. You ve got no chance him using modern fandangos like emails" welcome to the 21 century

Sent from my D2303 using Tapatalk

 

[Rigsby]

I had a clear out last Novenber and came across some pre printed quotations from Nebbs. Triplicate carbon copies. Found a load of 3.5" floppy disc's as well from 1994 to 2004.

My missus still has her Hermes typewriter from 1976. Think the ribbon will have dried out by now.