Nozzle for thin coat

[Butler]

Hey you guys, can anyone help, I bought a mtec 100 a few weeks back and went to use 1.5mm top coat though it today but it was not blowing out fast enough to give the textured finish, compresser was running at 2bar as normal, just wondering what size nozzle should I be using, I was given a 12mm one, should it be smaller?

Thanks

Gary

 

[DaveAndersonREP]

Hi Gary what gun do you have on it is the cap a rubber one


Sent from my iPhone using Tapatalk

 

[MikeAtthis]

About 4/6 mm just big enough for the gear to come out I use on the ritmo with a separate compressor


Sent from my iPhone using Tapatalk

 

[DaveAndersonREP]

It's a different gun on the m100 to the ritmo


Sent from my iPhone using Tapatalk

 

[Butler]

Hi Dave. It has a brass cap with rubber washer with the 12mm nozzle that you screw to the gun

 

[MikeAtthis]

So what size then dave


Sent from my iPhone using Tapatalk

 

[DaveAndersonREP]

Ok you will need a 4 mm the nozzle size should be 3 X the material grain size 2 mm grain =6mm nozzle
1.5 = 4 mm as we don't do a 4.5


Sent from my iPhone using Tapatalk

 

[Butler]

out I use on the ritmo with a separate compressor

Thanks Mike, so a 12mm is way to big then

 

[MikeAtthis]

Lol so 4 it is then


Sent from my iPhone using Tapatalk

 

[MikeAtthis]

Thanks Mike, so a 12mm is way to big then

Different machine mate same principles


Sent from my iPhone using Tapatalk

 

[DaveAndersonREP]

[emoji1417]


Sent from my iPhone using Tapatalk

 

[Rigsby]

Is 2 bar adequate for thin coat?

 

[Butler]

emoji1417

Hi Dave. I got the machine off you boys, can I give you a ring tomorrow for a quick chat.
Thanks
Gary​

 

[DaveAndersonREP]

Yes Gary not problem my mobile number is 07773 286659


Sent from my iPhone using Tapatalk

 

[DaveAndersonREP]

Yes rigsby with the correct spray nozzle


Sent from my iPhone using Tapatalk

 

[UKPlasteringmachines]

2 bar sounds awfully low for topcoat ours run at 4

 

[DaveAndersonREP]

Also the volume as well though


Sent from my iPhone using Tapatalk

 

[HLR External Renders]

Butler how did you get on spraying mono through the m100

 

[MikeAtthis]

Also the volume as well though


Sent from my iPhone using Tapatalk

what compressor would you recommend then dave

 

[Plasterers1StopShop]

Hi Gary,

2 bar pressure is more than adequate for spraying Thin coat Renders. When using the EZE 24 which IMO is the best machine on the market for spraying thin coats you can spray running off 1.8 bar.

The nozzle you have is too large for what you require, we are sending another out to you - can you call me Monday to confirm, I will try and call you now.

 

[DaveAndersonREP]

Mike we use our own Eze compressor with our Eze 24 and the M100, I know that the setup on the ritmo is different from our machines as we don't use our own spray gun


Sent from my iPhone using Tapatalk

 

[MikeAtthis]

A machine is a machine same principles what is the air volume on yours and does it come in 240v not much information on your website


Sent from my iPhone using Tapatalk

 

[Plasterers1StopShop]

A machine is a machine same principles what is the air volume on yours and does it come in 240v not much information on your website


Sent from my iPhone using Tapatalk

We don't sell 240v machines as you already know Mike. The data we give is enough. Our machines and are designed and suited to the required applications.

 

[MikeAtthis]

So no good if I wanted it for something else then


Sent from my iPhone using Tapatalk

 

[Plasterers1StopShop]

So no good if I wanted it for something else then


Sent from my iPhone using Tapatalk

It gives the required volume for a wide range of machines including what you use. We don't just sell them as individual units though to be honest, we keep them with our machines.

 

[Butler]

Butler how did you get on spraying mono through the m100

With my thin coat jobs going not got to the mono job yet, I'll post you when I've had a go. Cheers bud

 

[Butler]

Hi Gary,

2 bar pressure is more than adequate for spraying Thin coat Renders. When using the EZE 24 which IMO is the best machine on the market for spraying thin coats you can spray running off 1.8 bar.

Cheers for today, can you send me a hose holder that clips on the scaffold mate, I'll give it a go.
Thanks Ryan

Gary

 

[Butler]

Yes Gary not problem my mobile number is 07773 286659

Thanks Dave all sorted Ryan is sending me a 4mm thanks for every thing

 

[DaveAndersonREP]

No problem Gary


Sent from my iPhone using Tapatalk

 

[Arti]

@DaveAndersonREP
Alreet Dave the Rave been looking at the eze compressor for spraying acrylic etc. Does it come with air hoses etc? What else would I need to use it?

 

[User___removed]

Thought you had a ritmo arti?

 

[Arti]

Thought you had a ritmo arti?

I do. I just want something to spray acrylic and slurry coats etc

Sent from my D2303 using Tapatalk

 

[User___removed]

Ritmo will do!!
Just need to spend a couple grand
Seems silly buying another machine

 

[Arti]

Ritmo will do!!
Just need to spend a couple grand
Seems silly buying another machine

On what?

Sent from my D2303 using Tapatalk

 

[User___removed]

On what?

Sent from my D2303 using Tapatalk

What does on what mean?