Scrap times

[Arti]

:RpS_laugh:

 

[Andy M]

3 nuggets for a bead....? I hope you told em to get lost

Just got the chitty out and its 3.06 plus for angles and 3.24 for stop plus vat. I use this place on and off but there prices have gone through the roof. Decent enough beads like(Renderplas)but not had a problem with Encons.

 

[vinnie2]

yea that old vat eh/

 

[keithuk]

What worries me is it is all going up and that is before January when they normally put their prices up :RpS_scared:

 

[plasterjfe]

Encon chorley usually do delsy. Very good bead. Don't warp after 1 day out the box.

I hate cheap made beads.

Dbp will do a deal on n masterbead

 

[keithuk]

Just got the chitty out and its 3.06 plus for angles and 3.24 for stop plus vat. I use this place on and off but there prices have gone through the roof. Decent enough beads like(Renderplas)but not had a problem with Encons.

is that for the wider bead ?

 

[Andy M]

Dont worry Keith, the Bullnose look is bound to come back soon

 

[keithuk]

Dont worry Keith, the Bullnose look is bound to come back soon

[h=4]Wide angle / corner bead: 57mm wing for external rendering :rolleyes)[/h]

 

[owls]

What worries me is it is all going up and that is before January when they normally put their prices up :RpS_scared:

everything goes up nothing comes down,
enewalls just gone up 5% end of September, parex are up again in January 7% and inflation is only 2%. at this rate ill have to get my smoked salmon from Aldi instead of marks and spencer. :-0

 

[keithuk]

everything goes up nothing comes down,
enewalls just gone up 5% end of September, parex are up again in January 7% and inflation is only 2%. at this rate ill have to get my smoked salmon from Aldi instead of marks and spencer. :-0

That will be the day :RpS_lol:

 

[Putzmiester]

Wow u lads r paying a lot for bead I pay 1.80 for rendplas lovely bead to use

 

[Andy M]

is that for the wider bead ?

No its for the standard Keith.

 

[keithuk]

Wow u lads r paying a lot for bead I pay 1.80 for rendplas lovely bead to use

How many boxes do you have to buy for that price mate ?

 

[keithuk]

No its for the standard Keith.

it,s a bit high then mate ,i only buy the wider one these days

 

[Rigsby]

DBP have different beads at different prices. I like Pro bead but they cost. Rendaplas are good. The cheap beads in the cold snap and break when you cut them. A good bead cuts no problem.

SAS has an interesting bead with a built in drip for the soffits of openings. Only 6mm at the moment though.

 

[plasterjfe]

DBP have different beads at different prices. I like Pro bead but they cost. Rendaplas are good. The cheap beads in the cold snap and break when you cut them. A good bead cuts no problem.

SAS has an interesting bead with a built in drip for the soffits of openings. Only 6mm at the moment though.

The masterbead are the dearer of the two

 

[Rigsby]

Probably the ones I have. I don't have their contract beads.

 

[kgreigh]

Did a same day scrape with weber couple of weeks ago, bout the time this thread was started, was only the front of a small house mind,24m2

 

[cjs]

Well no spraying this week in the west,rain all week so will finish the base coat tomorrow and let it stand for a week,some of it has already been base coated a week already.
I will be spraying e grade k rend in fintry stone next week if the weather is better,but I think it will be afternoon spray and left till the morning to scrape by then :RpS_crying:

 

[keithuk]

Heat wave on the way ,only for the south east , as we pay more tax :RpS_wink:..wait for it ....wait

 

[Rigsby]

You need to pay more tax in the South East to pay for the illegals B&B after coming into Dover under a lorry.

 

[keithuk]

You need to pay more tax in the South East to pay for the illegals B&B after coming into Dover under a lorry.

if you stop doing mate ,and use the boats as i said ,then it will be ok ,by the way you owe me a new exhaust :RpS_wink: