Uni and bg

theplasterman said:
Oh and in the real world plasterers skim over Artex Ceilings every single day.. Stick your board's up ...........
Click to expand...


Yes using pva and multi, there you go again as if reboarding is the only solution your the only one on here that likes it.

Tell me why does wickes not stock it ? I'll tell you why because plasterers don't want it, nor need it.
Some b&qs stock it but those I use Stevenage always end up reducing it, Bedford did stock it but had to reduce it and no longer stock it these are all facts that you and bg cannot hide from.

So stop telling lies.
 
gps said:
Yes using pva and multi, there you go again as if reboarding is the only solution your the only one on here that likes it.

Tell me why does wickes not stock it ? I'll tell you why because plasterers don't want it, nor need it.
Some b&qs stock it but those I use Stevenage always end up reducing it, Bedford did stock it but had to reduce it and no longer stock it these are all facts that you and bg cannot hide from.

So stop telling lies.
Click to expand...
He will either blame me or you on that lol I personally blame vince on its failure on this forum for his obvious bias towards it.
 
  • Like
Reactions: gps
flynnyman said:
He will either blame me or you on that lol I personally blame vince on its failure on this forum for his obvious bias towards it.
Click to expand...
I blame you flynny...i like gps cos he brought hook on beads into my life
 
A.plasterer said:
I've just eaten some dope :sisi:it's gonna be a mellow evening prob intervals of goofing out .:popcorn:
Click to expand...
And nice cold G&T
Uni and bg
 
Re the other thread "forum meet up", don't think I want to go now, bit frightened tbh Might be best to get a bit of hug, where's that "women plasterers" thread gone, there's a couple of beauty's on there.............
 
The White spots are probably one of two things, either bits of polymer or Lime that haven't been mixed through properly during production
 
smudge505 said:
The White spots are probably one of two things, either bits of polymer or Lime that haven't been mixed through properly during production
Click to expand...

They are lime, was told this around 6 months ago by bg insider. The batch hadtoo much moisture content at mixing in stage. That's why you sometimes get it in multi or board too.
 
Insider Lol I doubt it's Lime it has 1 % in Multie and its Used for a reason and I doubt it's used in the uni for this reason. It's basics, lets
Not bullshit each other it's basic science that you will learn in a proper apprenticeship, gets back to what I always say the basics are missed out.
 
Insider haha..wats next bbc panaroma..f**k me I'm bored waiting for boxing to start wish wud of gone out now and got smashed
 
Kitchy said:
Insider haha..wats next bbc panaroma..f**k me I'm bored waiting for boxing to start wish wud of gone out now and got smashed
Click to expand...
It's never too late pal, spontaneous parties are best!

Sent from my Nexus 6P using Tapatalk
 
I'm friends with someone in the labs at one of the plants and I asked him regards the white spots and he confirmed that it is the lime, they sometimes get problems with the lime not being distributed or mixed through the 3.5 ton batch properly and so even though each bag is supposed to contain less than 1% sometimes due to the dispersal system that is used it can mean the lime isn't mixed through properly.
 
smudge505 said:
I'm friends with someone in the labs at one of the plants and I asked him regards the white spots and he confirmed that it is the lime, they sometimes get problems with the lime not being distributed or mixed through the 3.5 ton batch properly and so even though each bag is supposed to contain less than 1% sometimes due to the dispersal system that is used it can mean the lime isn't mixed through properly.
Click to expand...
Try telling that to flynny!
 
You must log in or register to reply here.

Share this page

Back
Top