Pj

[Ppj]

Hi lads av got a big k rend job in the middle ov the gable is a circular window would a plastic stop bead do the job

 

[spunky]

If you did try bending it a bell cast would maybe look better with the bead arris
Tbh I’ve never done one if it’s a small window I’d imagine the only way would be a timber former and free hand the next pass or an angle bead with loads of cuts in it but they can still look like a 50p piece

 

[spunky]

Especially at the joint

 

[malc]

Hi lads av got a big k rend job in the middle ov the gable is a circular window would a plastic stop bead do the job

Use a plastic arch bead

 

[themucky1]

6mm ply all round the inside of the reveal cut it to the thickness of your finish when the finish has dried remove the ply and render the reveal

 

[Dollar]

6mm ply all round the inside of the reveal cut it to the thickness of your finish when the finish has dried remove the ply and render the reveal

Ridiculous ——————————————————————-
Wakey wakey

 

[Salfordspread]

Ridiculous ——————————————————————-
Wakey wakey

Whys test ridiculous then ??

 

[spunky]

Use a plastic arch bead

Do they make them malc at a render thickness I’ve only seen them for skimming

 

[Salfordspread]

Do they make them malc at a render thickness I’ve only seen them for skimming

Neither have I

 

[Dollar]

Whys test ridiculous then ??

ridiculous
Get a bead on ,
Fux around & find out

wakey wakey

 

[essexandy]

Do they make them malc at a render thickness I’ve only seen them for skimming

Yes they do mate, I've used them a good few times.

 

[ChrispyUK]

Yes they do mate, I've used them a good few times.

No you haven’t

 

[Salfordspread]

ridiculous
Get a bead on ,
Fux around & find out

wakey wakey

I've never seen an arch float bead send a picture of one

 

[Dollar]

I've never seen an arch float bead send a picture of one

Neither have I
Wakey wakey

 

[essexandy]

I've never seen an arch float bead send a picture of one

Redirect Notice

 

[bobski]

Neither have I
Wakey wakey

Wakey wakey indeed



Have to thank Andy for teaching you now.



Off you trot.

 

[Dollar]

Redirect Notice

Not a Float bead !!! ——pay attention ____________________
Wakey wakey

 

[themucky1]

Ridiculous ——————————————————————-
Wakey wakey

Shut up you shill!

 

[themucky1]

Redirect Notice

That’s only 6mm pal, assuming when they say k-rend they mean mono minimum thickness should be approximately 12mm

 

[Cockney]

 

[essexandy]

That’s only 6mm pal, assuming when they say k-rend they mean mono minimum thickness should be approximately 12mm

I was replying to Damien about a arch render bead, they work just fine with sand and cement.
We've had them in the past with a 10mm arris as well and used those with Parex Monoblanco.

 

[Salfordspread]

That’s only 6mm pal, assuming when they say k-rend they mean mono minimum thickness should be approximately 12mm

Exactly he's on about mono not thin coat the plot thickens

 

[Salfordspread]

I was replying to Damien about a arch render bead, they work just fine with sand and cement.
We've had them in the past with a 10mm arris as well and used those with Parex Monoblanco.

That's only 6mm that's why ply is a better option unless there's a thicker one out there fik knows

 

[Salfordspread]

That’s only 6mm pal, assuming when they say k-rend they mean mono minimum thickness should be approximately 12mm

Neither have I
Wakey wakey

BELLEND