new system for bead fixing

[tapit]

I.m confused at first I thought it was a tape that you put on instead of beed but is it tape you use to stick beeds on with

yes mate

 

[lurpak]

So it’s a system for perfectly boarded angles. Bout as useful as a cock flavoured lollipop

 

[tapit]

It won’t re-emulsify the pva so will just pull the pva off.

 

[John j]

So it’s a system for perfectly boarded angles. Bout as useful as a cock flavoured lollipop

Bet I could do it quicker with clouts on board then using tape

 

[tapit]

not with you on that one?

 

[Cockney]

Come on ffs! just cut to the chase how much is it?? Lol

 

[tapit]

Bet I could do it quicker with clouts on board then using tape

how many clouts do you use?
i think i could stick three pieces of tape quicker time after time, cut stick, instead of hold, hammer ouch .

 

[lurpak]

not with you on that one?

Back to the drawing board

 

[tapit]

Come on ffs! just cut to the chase how much is it?? Lol

probably similar to a good quality scrim

 

[lurpak]

how many clouts do you use?
i think i could stick three pieces of tape quicker time after time, cut stick, instead of hold, hammer ouch .

Depends. A few. Only need to hold
It in place

 

[Cockney]

How much???

 

[tapit]

So it’s a system for perfectly boarded angles. Bout as useful as a cock flavoured lollipop

most new build and domestic skim angles are not far out

 

[John j]

how many clouts do you use?
i think i could stick three pieces of tape quicker time after time, cut stick, instead of hold, hammer ouch .

As few as it needs till its tight allway up corner. . How longs each strip of tape

 

[tapit]

As few as it needs till its tight allway up corner. . How longs each strip of tape

as long as you cut it,i use one strip horizontal agross bead about 75mm long

 

[Cockney]

 

[tapit]

it also pulls bead in tight no wobbly slack

 

[John j]

as long as you cut it,i use one strip horizontal agross bead about 75mm long

That wouldn't hold beed enough for me

 

[Deleted member 32554]

most new build and domestic skim angles are not far out

One more point, would it be as stable wit laying on in comparison to these other diy methods

 

[Cockney]

it also pulls bead in tight no wobbly slack

 

[tapit]

That wouldn't hold beed enough for me

i meant the length,four strips max on 2,4 bead at same centres as BS for mechanical fixing

 

[tapit]

One more point, would it be as stable wit laying on in comparison to these other diy methods

as good as or better than all other systems and so simple

 

[Danny]

you have two slow systems,this replaces both and is quicker and no sore thumbs,you could however use the tape to wrap around your thumbs before hitting that tiny clout into rock hard concrete

Email me davlicmedia@gmail.com and I will take a closer look

 

[lurpak]

 

[tapit]

Email me davlicmedia@gmail.com and I will take a closer look

Email me davlicmedia@gmail.com and I will take a closer look

ok, i will send over some drawings prob tomorrow now. cheers

 

[Cockney]

Are you Mutt & Geoff!!!!! Hooooow muuuch!!

 

[Deleted member 32554]

as good as or better than all other systems and so simple

How thick is it, any concern over the void created on surrounding bead area , would consider contact adhesive perhaps , just spray inside of bead if reveals are checked and press on

 

[tapit]

Are you Mutt & Geoff!!!!! Hooooow muuuch!!

i am hard of hearing unfortunetly, its still in research stage but i would envisage less than fiver which would be enough for typical three bed house

 

[tapit]

How thick is it, any concern over the void created on surrounding bead area , would consider contact adhesive perhaps , just spray inside of bead if reveals are checked and press on

0.2mm

 

[tapit]

How thick is it, any concern over the void created on surrounding bead area , would consider contact adhesive perhaps , just spray inside of bead if reveals are checked and press on

faster and cleaner with no waste or empty cans

 

[John j]

Email me davlicmedia@gmail.com and I will take a closer look

Free loading f**k*r lol

 

[Groove37]

i am hard of hearing unfortunetly, its still in research stage but i would envisage less than fiver which would be enough for typical three bed house

Send me a roll to try I’m genuinely intrigued

 

[Cockney]

i am hard of hearing unfortunetly, its still in research stage but i would envisage less than fiver which would be enough for typical three bed house

How much is on a roll then?

 

[tapit]

Send me a roll to try I’m genuinely intrigued

i only have small sample amount but i will give some out to try if and when it takes off.
i am just beginning market research at the moment and you are first guys ive shown too

 

[tapit]

How much is on a roll then?

still not finalised roll sizes but your feedback as to size and price appreciated

 

[tapit]

ok, got to go.
Thanks all for listening and for critical feedback.